Gatineau Concrete applies SikaTop underlayments and SikaFloor epoxy, urethane, and specialty coatings to industrial and commercial slabs. The Sika floor range spans self-leveling tolerance correction, high-performance toppings for chemical and mechanical wear, conductive systems for electronics manufacturing, and food-grade urethane for processing plants. We match the system to your facility's actual demands, then install to Sika specification so the warranty covers both material and workmanship. Free written estimate on every project.
SikaFloor is not a single product but a family of floor systems, each engineered for different facility conditions. SikaTop self-leveling products flatten slabs before finish coatings go down, correcting minor surface irregularities so the topcoat applies evenly. SikaFloor epoxy and polyurethane systems provide the wear layer, with formulations for standard industrial use, chemical resistance, ESD conductivity, and food-processing compliance.
We assess your facility's traffic patterns, chemical exposure, temperature swings, and any regulatory requirements (USDA, CFIA, electronics cleanroom standards), then select the matched SikaFloor system. Installation follows Sika's technical specification for that system: substrate prep, primer application, body coat thickness, topcoat, and cure schedule. This specification-driven approach is what makes the Sika system warranty meaningful.
We walk the space, document traffic type (foot, forklift, vehicle), chemical exposure (oils, solvents, food acids), temperature cycling, and any compliance needs (ESD, food-grade, anti-slip). This assessment drives system selection.
Prepare slab to system spec
The concrete slab is diamond-ground to the profile required by the chosen SikaFloor system, old coatings and contaminants removed, cracks repaired with Sika-compatible materials, and the surface cleaned and primed with the matched Sika primer.
Apply SikaFloor layers in sequence
The body coat is applied at engineered thickness, aggregate broadcast where slip resistance is specified, and the topcoat applied per system cure schedule. Each layer cures fully before the next begins.
Document and release for service
Material batch records, application thickness readings, and cure schedule are documented for warranty support. The floor is handed off with maintenance protocol and the Sika system warranty in place.
System selection
Why System Matching Determines SikaFloor Success
A SikaFloor system chosen for the wrong facility fails predictably. A chemical-resistant urethane that handles solvents but lacks forklift-load durability will spall under wheel traffic. An epoxy rated for mechanical wear but not chemical exposure will degrade under spill exposure. The system match is the engineering decision that makes the floor perform for years.
We pair facility assessment with knowledge of the full Sika range, so the system we recommend is the one that will actually survive your facility's conditions. Coordinate with Sika repair for substrate issues, Sika waterproofing for moisture management, and our industrial concrete services for facility-wide floor programs.
System choice, ESD, chemical resistance, warranty and facility match.
Based on the use, traffic, chemical exposure, and any specialty requirements (ESD, food-grade, anti-slip). We confirm the actual conditions during the assessment and recommend the matched system from the Sika range.
Yes, with the conductive/dissipative SikaFloor systems engineered for ESD-sensitive electronics manufacturing and clean rooms. The resistance range is verified after install.
Yes, Sika has urethane cement systems with cove base integration for USDA/CFIA-compliant food processing floors. Cross-reference with our food-grade epoxy flooring service.
Yes when installed by a Sika-system installer to Sika spec. System warranty extends beyond product to install integrity, which is what commercial customers actually need.
Per zone, typically a week including cure before service. Larger facility-wide projects stretch with phased install. Schedule is in the quote.
SikaFloor urethane in our chemical handling zone. Three years of daily exposure, no degradation. The matched system spec made the difference.
Q. A6
Industrial Operations, Gatineau
★★★★★
ESD SikaFloor across our assembly zones. Resistance verified at install, documentation supports our customer audit. Real specialty system delivery.
Y. A6
Plant Manager, Ottawa
★★★★★
SikaTop self-leveling to bring slabs flat for tile install. Tile contractor said it was the easiest substrate he had worked on in months. Trade coordination paid off.
Z. A6
Facility Director, Barrhaven
★★★★★
They picked the right SikaFloor system for each zone in our multi-use facility, not one system everywhere. Better engineering, better outcomes.
X. A6
Operations Lead, Nepean
From the blog
Concrete Guides & Articles
Practical reading on planning, finishes and caring for concrete in Gatineau.
Describe your facility use, zone layout, and any specialty requirements. We will assess the slab, recommend the matched SikaFloor system, and send a written quote with schedule.
